Brand: Unbranded
SAFE & SECURE SHOPPING 100% SATISFACTION GUARANTEED FAST SHIPPING You may also like You may also like 19 IN 1 Arcade Classics Jamma Board VGA CRT/LCD PCB Video Arcade Board 53.99 USD For Sony PlayStation 5/4 RJ45 Port Interface Ethernet Connector Accessories 7.99 USD 3.99 USD 65mm RGB Cooler Radiator Phone Tablet Game Semiconductor Heatsink Cooling Fan 13.99 USD 3.99 USD For PS5 Slim Games Console External Cooling Fan Disc Digital Version RGB 14.99 USD 3.99 USD 3-Port External USB 2.0 Expansion Hub Splitter Adapter For PS5 Slim Console 8.99 USD 3.99 USD Plastic & Metal Fixed Power Button Switch Board For Sony PSP 3000 Console 9.39 USD Gaming Accessories for JVS to USB Controller Adapter MP07- IONA-US for TTX2 TTX3 Product Description Features: Compatible with for Xbox 360 / for Xbox One series/for PS4/for PS3/for Switch pro controllers. Custom Button Layout, map at most 12 physical buttons to arbitrary logical buttons for JVS. Rapid-fire,enable rapid-fire mode per each physical button. Persistent Configurations, store and restore at most 10 configuration sets of button layout, rapid-fire settings, and it’s speed Firmware Updates,For bug fixes, or to improve compatibility, firmware updates are available. Twin stick mode, When a for PS4 controller is connected to the 1P USB port, pushing PS button switch operation mode between the normal mode and the twin stick mode. Mahjong mode,When a USB keyboard supporting boot mode, though almost all keyboards will support, is connected, IONA switches to mahjong mode. Settings: Transit operation modes On boot, IONA runs in the normal mode. Operation modes are transited by pressing TEST and SERVICE buttons on the IONA board. ① Normal mode (LED - blink or on, depending on JVS bus state) Works as a JVS I/O controllers with chosen settings. ② Layout config mode (LED - fast blink) On pushing TEST and SERVICE together, it enters the layout config mode. you need to press both for at least 0.5 and at most 5 seconds together. You don’t need to push them exactly together, e.g. keeping TEST down and clicking SERVICE will work. In the button layout mode, you will choose physical buttons in the following order, coin, start, button1 to 10. If you push multiple buttons together, you can assign multiple physical buttons into one button. You don’t need to push them at the eaxctly timing as well. When you press a button, IONA starts recording all pressed buttons until all buttons are released, then assign them all to the target button. You continue this sequence until all 12 buttons are mapped. If you leave this mode before settings all, remaining buttons are remained to have no assignment. If you configure no button, exceptionally IONA doesn’t update layout at all and move to the next mode. ③ Rapid-fire config mode (LED - blink) You can press multiple physical buttons for which rapid-fire is enabled. Similarly, timing should not be exact. You can try multiple time until existing from this mode. ④ Speed config mode (LED - slow blink) You can choose rapid-fire speed by button 1 - 6. Button 1 - 6 does not mean the physical buttons, but buttons mapped in the custom layout. Each button 1 - 6 are mapped to 30/20/15/12/10/8.5 fps. You can try any time until exiting from the mode. If you push multiple buttons, faster speed is taken. If release timing differs, the latter one is taken. Chosen settings above will be stored persistently. ⑤ Factory reset (LED - flash) You can reset all settings and restore default settings by pressing TEST and SERVICE together outside the normal mode. LED flashes, then go back to the normal mode automatically. ⑥ Call store config (LED - off) You can enter the mode to call stored config by pushing SERVICE button outside the normal mode. Pressing button 1 - 10 in the custom layout recall the configuration set 1 - 10. Initial set for the factory setting is 1. You can recall another config again until exiting the mode by pressing SERVICE again. It returns to the normal mode if the firmware is older than 1.40 by pressing SERVICE. Otherwise, ver 1.40 and later, pressing TEST moves to the analog layout config mode. ⑦ Analog layout config mode (LED - fast blink) You can choose 6 inputs for analog signal reports. Analog input values are remembered as base values when you enter this mode. You can move an analog stick or a trigger that are recognized as analog inputs. You may want to move it right, down, or pushed for normal polarity. If you want to revese it, you can move it toward the opposite side. Once you stop moving the stick or the trigger and make it return to the original position, the input was recorded. You need to repeat the same steps for analog input 1 to 6, 6 times. You can quit this mode by pressing TEST, and following assignments are just skipped and previous settings are used. ⑧ Options config mode (LED - blink) You can quit the settings mode by pressing TEST, but options will be set via P1 buttons on quitting the mode as below. The button number is logical one based on. USE Guide: 1. Connect USB Type C port for power supply. It doesn’t need data connection as it’s just expected to suupply 5V power for IONA. USB charger will be available. Of course, PC USB port can support the required power. PC-based JVS system board could have a port for this use, e.g. exA-Arcadia has hidden USB ports. But if you want to use a device that requires much power, supplying via USB Bus from PC may not be enough and IONA gets to be unstable. 2. Connect JVS port to the JVS system board. You can use a general USB cable. 3. Connect USB gamepads at any time Package include: 1* JVS to USB Adapter (Does not include any cables or chargers) About Us Payment Shipping Returns Contact Us About Us Our company adheres to the principle of integrity first, customer first to serve our customers. Our products are of high quality and are very popular with consumers. The products are not only high quality and low price, but also exported to many regions abroad. Payment We only accept Ebay payments from verified accounts with confirmed addresses. Orders will be shipped after receiving cleared payment. Shipping Item(s) will be shipped within 2 business days after payment is cleared. If you want faster shipping way. Please contact us before making payment. Sometimes due to problems with our transportation company system, your shipping information may be delayed to update. We recommend that you try again after 3-4 days. If you still haven't checked the shipping information, you can contact us. Returns If you have any questions, please feel free to email our service specialists 24 Hours a Day, 7 Days a Week. We will reply you as soon as possible. Return/refund is accepted within 30 days after the buyer receives the item. NO exchange will be accepted after 30 days from the date when the item is received. Please contact us first before returning your product!!! Contact Us If you have any questions, please feel free to contact us. We will reply to you as soon as possible and solve it for you. At the same time, we will uphold the concept of service first, and serve you wholeheartedly. We hope every time you shop is a pleasant experience! Copyright © 2022 Tongtool